Category: 1074-82-4

In chemical reaction engineering, simulations are useful for investigating and optimizing a particular reaction process or system., 1074-82-4

General procedure: A 500 mL round-bottom flask was charged with4.63 g (0.025 mol) Phthalimide potassium salt, dissolve in 120 mL Anhydrousacetone. 6.9 g (0.05 mol) potassium carbonate and 11.75 g (0.0625 mol) 1,2-Dibromoethanewas added. The solution was heated to reflux for 8 h. The stirring mixture wasallowed to cool, and then was filtered. The solids were washed with 50 mL ofacetone, followed by 50 mL of EtOAc. The filtrate and the washer liquid werepooled and concentrated in a rotary evaporator, then purified by flashchromatography on SiO2 (gradient, 1:6 to 1:4 petroleum ether:EtOAc)to obtain 5.2 g (81.8%) of N-(2-Bromoethyl) phthalimideas a white solid.

Keep reading other articles of Potassium 1,3-dioxoisoindolin-2-ide! Don’t worry, you don’t need a PhD in chemistry to understand the explanations! I believe this compound will play a more active role in future production and life.

Reference:
Article; Si, Weijie; Zhang, Tao; Zhang, Lanxiang; Mei, Xiangdong; Dong, Mengya; Zhang, Kaixin; Ning, Jun; Bioorganic and Medicinal Chemistry Letters; vol. 26; 9; (2016); p. 2380 – 2382;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 1074-82-4, name is Potassium 1,3-dioxoisoindolin-2-ide, This compound has unique chemical properties. The synthetic route is as follows., name: Potassium 1,3-dioxoisoindolin-2-ide

To a stirred solution of i,6-dibromohexane (12.3 rnL, 81.0 mmol) in DMF (10 mL), was added potassIum phthaiate (5.0 g, 27,0 mrnoi) portion-wise over 30 mm at room temperature. After complete addition, the reaction mixture was stirred at 90 C for 18 h, then quenched with waLer (300 mL) and extracted with diethyl ether (150 mL x 2). The combined organic extracts were washed with water (100 mL x 2), followed by brine (50 mL x 2) and dried over anhydrous sodium sulfate, filtered and concentrated under reduced pressure. The resultant residue was purified by silica gel column chromatography (60-120 mesh) using 5-10% EtOAc / hexanes to afford 3-i as an off- white solid (6.3 g, 76% yield). LCMS: 310.95 (M+1).

In conclusion, we affirm that quantitative kinetic descriptions of catalytic behavior continue to navigate research efforts intended to implement such knowledge in the development of new catalytic chemistries. Read on for other articles about 1074-82-4.

Reference:
Patent; CV6 THERAPEUTICS (NI) LIMITED; SPYVEE, Mark; SHIRUDE, Pravin S.; (258 pag.)WO2017/6282; (2017); A1;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

COA of Formula: C8H4KNO2, Chemistry built the modern world, from the materials that make up the everyday objects around us, the batteries in our devices and cleaning products that help to maintain sanitation.

General procedure: A mixture of dibromoalkane (23 mmol) and potassium carbonate (12 mmol)was added in acetone (30 mL), and potassium phthalimide (10 mmol) was added slowly over a 15-min period, and then the reaction was heated under reflux for 8-10 h. The reaction mixture was filtered,and the acetone was evaporated in vacuo. The crude product was purified by column chromatography on silica gel using mixtures of petroleum/acetone as eluent) to obtain the white solid compounds 2-4.

Keep reading other articles of Potassium 1,3-dioxoisoindolin-2-ide! Don’t worry, you don’t need a PhD in chemistry to understand the explanations! I believe this compound will play a more active role in future production and life.

Reference:
Article; Pan, Wanli; Hu, Ke; Bai, Ping; Yu, Lintao; Ma, Qinge; Li, Tao; Zhang, Xu; Chen, Changzhong; Peng, Kelin; Liu, Wenmin; Sang, Zhipei; Bioorganic and Medicinal Chemistry Letters; vol. 26; 10; (2016); p. 2539 – 2543;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

With the volume and accessibility of scientific research increasing across the world, it has never been more important to continue building the reputation for quality and ethical publishing we’ve spent the past two centuries establishing., Application of 1074-82-4

a) Preparation of 6-bromohexylphthalimide Potassium phthalimide (5.4 mmoles) was added to a solution of 1,6-dibromohexane (3.95 g; 16.2 mmoles) in dimethylformamide (8 ml) and heated to 80C approx. under stirring. Reaction times and process as per Example 4. 2.46 g of pure product were obtained. Yield 66%.

The design and synthesis of related molecules that are more effective, more selective, and less toxic than aspirin are important objectives of biomedical research.Keep reading other articles of Potassium 1,3-dioxoisoindolin-2-ide.

Reference:
Patent; MEDIOLANUM FARMACEUTICI S.P.A.; EP575954; (1993); A1;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

Chemistry graduates have much scope to use their knowledge in a range of research sectors, including roles within chemical engineering, chemical and related industries, healthcare and more. , 1074-82-4

50 mL of DMF, 0.025 mol of the potassium salt of phthalimide, 0.10 mol of 1,4-dibromobutane and 0.5 g of TBAB, reaction at 70 C. for 2.0 h; cooling to room temperature, pouring into ice water, extraction with ethyl acetate, After washing with water, drying and desolvation, the mixture was allowed to stand overnight to precipitate 5.82 g of N-(4-bromobutyl)phthalimide as a white solid, mp 78-81C, yield 82.5%.

Interested yet? This just the tip of the iceberg, You can reading other blog about 1074-82-4.

Reference:
Patent; Hunan University; Hu Aixi; Yang Zihui; Li Jingwen; (9 pag.)CN107540647; (2018); A;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

Career opportunities within science and technology are seeing unprecedented growth across the world, and those who study chemistry or another natural science at university now have increasingly better career prospects. Recommanded Product: Potassium 1,3-dioxoisoindolin-2-ide

General procedure: Potassium phthalimide (0.93 g, 5 mmol) was added to a solution of 1,2-dibromoethane (1.3 mL, 15 mmol) in DMF (8 mL). The mixture was stirred at room temperature overnight and evaporated the solvent in vacuo, the residue dissolved in H2O and extracted with ethyl acetate. The organic layer was washed by brine and dried by MgSO4. Filtered and the solvent evaporated in vacuo, recrystallized from ethyl acetate to give white solid (566 mg, 45 %).

Keep reading other articles of Potassium 1,3-dioxoisoindolin-2-ide! Don’t worry, you don’t need a PhD in chemistry to understand the explanations! I believe this compound will play a more active role in future production and life.

Reference:
Article; Zhang, Wei; Zhou, Xin-Yang; Yu, Qin-Ying; Du, Lu-Pei; Li, Min-Yong; Chinese Chemical Letters; vol. 27; 2; (2016); p. 185 – 189;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 1074-82-4, name is Potassium 1,3-dioxoisoindolin-2-ide, This compound has unique chemical properties. The synthetic route is as follows., Application In Synthesis of Potassium 1,3-dioxoisoindolin-2-ide

a) Preparation of 5-bromopentylphthalimide Potassium phthalimide (5.4 mmoles) was added to a solution of 1,5-dibromopentane (3.72 g; 16.2 mmoles) in dimethylformamide (8 ml) and heated to 80C approx. under stirring. After 2 hours, water was added and the solution was repeatedly extracted with ether. The collected organic phases were washed with water, dried on Na2SO4 and evaporated under reduced pressure to give a solid (4.50 g), which was purified by chromatography on silica gel (Etp/Et2O 8:2) yielding 2.38 g of a white solid. Yield 68%.

Keep reading other articles of Potassium 1,3-dioxoisoindolin-2-ide! Don’t worry, you don’t need a PhD in chemistry to understand the explanations! I believe this compound will play a more active role in future production and life.

Reference:
Patent; MEDIOLANUM FARMACEUTICI S.P.A.; EP575954; (1993); A1;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

Related Products of 1074-82-4,When developing chemical systems it’s of course important to gain a deep understanding of the chemical reaction process.

(0331) A mixture of potassium phthalimide (100.0 g, 539.9 mmol, 1.0 equiv.), potassium carbonate (11.2 g, 81.0 mmol, 0.15 equiv.) and N,N-dimethylformamide (DMF) (200 mL) is treated with chloroacetone (47.3 mL, 54.9 g, 593.9 mmol, 1.1 equiv.) at a rate to control the internal temperature at not more than 40 C. After the addition is complete, the reaction mixture is stirred for about 12 hours at about 20-25 C. Water (333 mL) is charged to the reaction mixture at a rate to control the internal temperature at not more than 30 C. The mixture is stirred at about 20-25 C. for about 1 hour, and then the mixture is filtered. The filter cake is washed with water (200 mL), and the product is dried at about 70-80 C. under vacuum with a nitrogen flow for about 12 hours. The product phthalimidoacetone (VII-j) is obtained as a white solid (90.2 g, 97.3 wt. % purity, 80% yield).

The design and synthesis of related molecules that are more effective, more selective, and less toxic than aspirin are important objectives of biomedical research.Keep reading other articles of Potassium 1,3-dioxoisoindolin-2-ide.

Reference:
Patent; Boehringer Ingelheim International GmbH; DANG, Mai Thi Quynh; HAMPEL, Thomas Armin; KOCH, Sandra; NORDSTROM, Fredrik Lars; REEVES, Jonathan Timothy; REICHEL, Carsten; SCHOERER, Marvin; STANGE, Christian; VOLCHKOV, Ivan N.; Zhong, Li; ZIMMERMANN, Uwe Johannes; (38 pag.)US2018/251427; (2018); A1;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

Chemistry graduates have much scope to use their knowledge in a range of research sectors, including roles within chemical engineering, chemical and related industries, healthcare and more. , 1074-82-4

8.7ml (6 · 5 X 102 moles) 1,5-dibromopentane with6 g (3. 2 X 10 2 moles) Phthalimide potassium salt dissolved in 100ml of N, N- dimethylformamide andunder room temperatureit was stirred for 15hours.The solvent was distilled off under reduced pressure, The residue usingn-hexane: ethyl acetate with a volumeratio of 10: 1 eluent to carry out column chromatography, gradually increasingthe polarity to hexane: ethyl acetate with a volume ratio of 5: 1 to give a product of 6.9g(2.3X102 mol) a bromogroup substituted by Phthalimide. The product with 5. 9g (4. 7X 102 mol) of sodium sulfite, 140ml water and 85ml95% ethanol mixed reactionwas heated to 95 C for18h, the remainingsolvent was drained, and the resulting residue was mixed with 73ml ofconcentrated hydrochloric acidthen was heated to 110 C thefor 18H, it was drained, with water – 95% ethanol on the residue to carry out recrystallization to give 5-amino-1-pentylSulfonic acid 2. 7g (total yield 50%).

In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles, 1074-82-4, other downstream synthetic routes, hurry up and to see.

Reference:
Patent; Institute of Chemistry Chinese Academy of Sciences; zhao, jingquan; DENG, HONG; XEI, JIE; (16 pag.)CN101948412; (2016); B;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem

These common heterocyclic compound, 1074-82-4, name is Potassium 1,3-dioxoisoindolin-2-ide, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route. HPLC of Formula: C8H4KNO2

To a stirred solution of 1,6-dibromohexane (12.3 mL, 81.0 mmol) in DMF (10 mL), was added potassium phthalate (5.0 g, 27.0 mmol) portion-wise over 30 min at room temperature. After complete addition, the reaction mixture was stirred at 90 C for 18 h, then quenched with water (300 mL) and extracted with diethyl ether (150 mL x 2). The combined organic extracts were washed with water (100 mL x 2), followed by brine (50 mL x 2) and dried over anhydrous sodium sulfate, filtered and concentrated under reduced pressure. The resultant residue was purified by silica gel column chromatography (60-120 mesh) using 5-10% EtOAc / hexanes to afford 3-i as an off- white solid (6.3 g, 76% yield). LCMS: 310.95 (M+1).

Keep reading other articles of Potassium 1,3-dioxoisoindolin-2-ide! Don’t worry, you don’t need a PhD in chemistry to understand the explanations! I believe this compound will play a more active role in future production and life.

Reference:
Patent; CV6 THERAPEUTICS (NI) LIMITED; LADNER, Robert D.; (345 pag.)WO2018/128720; (2018); A1;,
Indoline – Wikipedia,
Indoline | C8H9N – PubChem